1974 Gibson Ripper

• Solid alder body • set three-piece maple neck • maple fretboard • 34 1/2 inch scale • twin humbuckers with Q-system electronics

Have a listen to this great vintage bass here

1975 Gibson bass guitar catalog

The earlier, wider, slab-bodied version of the Gibson Ripper was produced from the model's inception in 1973, through 1974. Compare this body shape, particularly the bevelling around the horns, with a later 1978 Gibson Ripper - these later Rippers have a far more sculptured look about them, although this is not always easy to see in photographs.

Like all Gibson Ripper basses, this guitar was built in the famous Kalamazoo plant (MI, USA) during the Norlin period of ownership.

1974 US zone 1 price for the Ripper was $449 in the January and June 1974 price lists, rising to $469 in November. A total of 1288 Rippers were shipped in 1974, with the vast majority in Natural finish as seen here, although many very early ones had a tobacco or cherry sunburst finish. See the Ripper shipping stats for further details.

This is a really punchy bass; lots of Gibson low end, but with so much more higher frequencies than Gibson's older basses.

see also 1976 Gibson Ripper, 1977 Fretless Gibson Ripper, 1978 Gibson Ripper

The Ripper body changed from this wider slab bodied bass, to a more sculptured version - see a 1976 Ripper with the newer body styling.

The alder grain patterns on this Ripper are clearly visible through the natural finish. Like the other 70s-designed basses, controls are scratchplate mounted, so requiring no rear control-cavity access.

The Ripper humbuckers are mounted with two screws through each pickup, and into the guitar's body wood. Not the most adjustable method... and Gibson soon improved upon this. Compare this 1974 (or any up until at least 1976) to the pickups of a later Ripper; Gibson then mounted them directly on to the scratchplate, but now with three screws. Note also the four polepiece screws, one under each string.

The Ripper's electronic circuitry, or Q-system consisted of a four way tone selector switch, volume control, mid range control and tone control. For a more about these controls see Gibson's Ripper controls description, but also listen to the 1974 Ripper promo record and some soundclips of this actual bass here
Like all early Rippers, the varitone position markers are on the metal switch marker ring - compare this with a later 1977 Ripper - which has these numerals engraved into the scratchplate.

All Ripper basses came equipped with the Gibson Three-point bridge with metal saddles. Extra long scale strings can be used, and strung through the body, as shown here, or standard long scale strings can be used, and strung directly from the bridge. The chrome-plated bridge cover has been removed for this picture.

Each string of the Gibson Ripper was able to be strung through the bass' body, entering from the rear, and passing over the bridge at the front. Early and middle period Rippers had four separate holes as shown here, but later these were covered by a 'four-hole eyelet' - see a 1977 Ripper for comparison.

The serial number on the back of the headstock still has six digits - a sure sign of an early Ripper. But precise dating of six digit s/n Rippers is not so easy - unlike the eight digit decals (see a 1976 Ripper serial number) or the eight digit stamp (see a 1978 Ripper serial number), there is no date encoded into the number. However from studying several Ripper basses, it would seem that the majority of six digit serial numbers starting 1 would have been shipped in 1974. The other headstock marking, the 'MADE IN U.S.A.' stamp, can be seen, though to some extent obscured by the tuning keys, if fitted.

The headstock of the Ripper bass was simple compared to basses of the previous decade; no fancy inlaid designs or logos, just black paint and a simple silk-screened 'Gibson'. Slight finish cracks can be seen where the wings attach running vertically down this bass' headstock. All Ripper truss rod covers had 'The Ripper' model designation, but early ones like this were one-ply black. Compare this to a later 1978 Ripper Truss rod cover with white revealed edging.

Three-piece neck and solid headstock. The three piece maple has two extra wings added at the headstock to give it a little extra width. 1973/74 open gear tuners. Seventies Gibsons (especially those with maple necks) typically have the volute where the neck meets the headstock; this strengthens the potentially weak area on the other side of the truss rod cavity.

Gibson Ripper soundclips

The Gibson Ripper bass is tonally very different from the 50s and 60s Gibson models that preceded it. Much more midrange frequencies, much more tonal definition and much more bite. With the four position switch, tone and midrange controls, there is a wide range of sounds available. The two sounds below were suggested in the 1974 Ripper promotional disk, and were recorded through a 1964 Ampeg B15. For more clips, check out the audio samples of this bass through various vintage valve amps here

Gibson Ripper bass for sale

Flyguitars.com is funded by its visitors. When you buy through links on our site we may earn an affiliate commission. For more info see terms and conditions.

Gibson Ripper (L9-S) Bass Guitar with Seymour Duncan

New Florence, Pennsylvania, 159**, UNITED STATES OF AMERICA

$3500

Gibson Ripper (L9-S) Bass Guitar with Seymour Duncan.
This bass is in very good condition. There are a few small marks located in the pictures. Feel free to ask questions, can send more pictures. Must have at least 10 positive comments to purchase. For sale in the United States Only
... more

1972 Gibson L6-S Bass Prototype (Ripper, Grabber) Singlecut Sunburst

Syracuse, New York, 132**, UNITED STATES OF AMERICA

$9000

1972 Gibson L6-S Bass Prototype (Ripper, Grabber) Singlecut Sunburst
 
This bass guitar is the prototype for the L6-S bass, a model that was never manufactured by Gibson. Although it is the prototype for an instrument that was not produced, it also seems to be a prototype of the Ripper and Grabber models introduced later that are constructed with the same materials (maple neck and body) and similar dimensions. The look of this one does foreshadow those later models
SETUP & ... more

Gibson L9S RIPPER 1976 Electric Guitar USA Vintage Rare Maple with Hard Case

Chesterfield, Virginia, 238**, UNITED STATES OF AMERICA

$3800

I bought this guitar around 1982. I played it in the high school marching band. It is a marvelous instrument that has always deserved a better player than myself. That being said, my only consolation in letting it go is that whoever owns it next plays the hell out it. They didn't call this model the Ripper for nothing and rock stars have long sought after this model built during this time. It sounds beautiful and it is painful for me to sell it. But I don't play it often and my home air ... more

1976 Gibson Ripper L9-S Vintage Bass Ebony Black

San Antonio, Texas, 782**, UNITED STATES OF AMERICA

$1990

1976 Gibson Ripper L9-S Vintage Bass Black. Condition is Used. Shipped with USPS Ground Advantage.
... more

1975 Gibson The Ripper L9-S Vintage Electric Bass Ebony, Alder Body w / Case

Seattle, Washington, 981**, UNITED STATES OF AMERICA

$3800

Up for sale, a 1975 Gibson "The Ripper" L9-S bass in 100% original condition and in perfect working order, complete with the original hardshell case. One of the more unique and versatile Gibson basses ever produced, the Ripper comes equipped with its original pair of Bill Lawrence designed "Super Humbucker" pickups and a four-way rotary switch for series, parallel, and out of phase pickup settings
The contoured alder body (as opposed to maple) is a particularly uncommon option, only offered ... more

Gibson L-9 S The Ripper Bass Guitar (Serial # 00157884)

Raleigh, North Carolina, 276**, UNITED STATES OF AMERICA

$2700

This vintage Gibson L9S RIPPER electric bass guitar is a rare find for any musician. Made in the United States in 1976, this guitar features a solid body type with a natural wood / clear body color. I inherited this bass and I am not a very musical person. I know it is in good shape and in working order. I will provide more pictures upon request. Serious inquiries only please
... more

Basse Gibson Ripper Fretless Black Ebony ~ 1976

Balanod, 39***, FRANCE

€2550

Superbe basse Fretless Gibson "The Ripper" L-9-SF Black, touche ébène, en très bon état. ~ 1976Configuration d'origine passive avec 2 micros humbuckers Bill Lawrence d'origine, sélecteur 4 positions d'origine, réglages Volume, Treble et Tone. Potentiomètres "CTS" et condensateurs "TAD Mustard" neufs. Chevalet d'origine avec pontets laiton réglables en hauteur individuellement. Etui d'origine usagé inclus
... more

1974 GIBSON GRABBER / RIPPER BASS CASE - made in USA

COLOGNE, GERMANY

€279

1974 GIBSON GRABBER / RIPPER BASS CASE - made in USA:
+ black tolex, has a lot of wear & rips
+ bottom is loose=check pic 7
+ strap that holds case open is gone
+ deep purple interior, has stains
+ 1 latch is broken=check last pic
+ handle was replaced
+ all feet on bottom are missing
Over 1000 more
GUITARS-BASSES-PARTS in our OTHER
AUCTIONS !!!!
TAKE A LOOK !!!... more

1974 GIBSON GRABBER / RIPPER BASS CASE - made in USA

COLOGNE, GERMANY

€350

1974 GIBSON case for RIPPER & GRABBER models:
+ black tolex, has a lot of wear & rips
+ rips & material missing at the plastic surround
+ strap that holds case open has a rip
+ deep purple interior, has some wear
+ all latches work fine
+ handle is gone
+ top of case is at headstock front resting on the bottom part=NOT OVRRLAPPING AS USUAL
+ all feet on back are missing
Over 1000 more
GUITARS-BASSES-PARTS in our OTHER
AUCTIONS !!!!
TAKE A LOOK ... more

Find more vintage guitars for sale at vintageguitarsforsale.co